close

 

hosts -->

/etc/hostname --> master.test.com
/etc/hostname --> node1.test.com
/etc/hostname --> node2.test.com

所有機器  hosts -->

192.168.0.65  master.test.com
192.168.0.67  node1.test.com
192.168.0.68  node2.test.com
192.168.0.69  node3.test.com

所有機器 
systemctl stop firewalld
systemctl disable firewalld
yum -y install ntp
systemctl start ntpd
systemctl enable ntpd

master  :
yum -y install etcd kubernetes flannel

設定 etcd to listen  addresses 
 /etc/etcd/etcd.conf

 
# [member]
ETCD_NAME=default
ETCD_DATA_DIR="/var/lib/etcd/default.etcd"
#ETCD_WAL_DIR=""
#ETCD_SNAPSHOT_COUNT="10000"
#ETCD_HEARTBEAT_INTERVAL="100"
#ETCD_ELECTION_TIMEOUT="1000"
ETCD_LISTEN_PEER_URLS="http://localhost:2380"
ETCD_LISTEN_CLIENT_URLS="http://0.0.0.0:2379"
#ETCD_MAX_SNAPSHOTS="5"
#ETCD_MAX_WALS="5"
#ETCD_CORS=""
#
#[cluster]
#ETCD_INITIAL_ADVERTISE_PEER_URLS="http://localhost:2380"
# if you use different ETCD_NAME (e.g. test), set ETCD_INITIAL_CLUSTER value for this name, i.e. "test=http://..."
#ETCD_INITIAL_CLUSTER="default=http://localhost:2380"
#ETCD_INITIAL_CLUSTER_STATE="new"
#ETCD_INITIAL_CLUSTER_TOKEN="etcd-cluster"
ETCD_ADVERTISE_CLIENT_URLS="http://localhost:2379"
#ETCD_DISCOVERY=""
#ETCD_DISCOVERY_SRV=""
#ETCD_DISCOVERY_FALLBACK="proxy"
#ETCD_DISCOVERY_PROXY=""
#
#[proxy]
#ETCD_PROXY="off"
#ETCD_PROXY_FAILURE_WAIT="5000"
#ETCD_PROXY_REFRESH_INTERVAL="30000"
#ETCD_PROXY_DIAL_TIMEOUT="1000"
#ETCD_PROXY_WRITE_TIMEOUT="5000"
#ETCD_PROXY_READ_TIMEOUT="0"
#
#[security]
#ETCD_CERT_FILE=""
#ETCD_KEY_FILE=""
#ETCD_CLIENT_CERT_AUTH="false"
#ETCD_TRUSTED_CA_FILE=""
#ETCD_PEER_CERT_FILE=""
#ETCD_PEER_KEY_FILE=""
#ETCD_PEER_CLIENT_CERT_AUTH="false"
#ETCD_PEER_TRUSTED_CA_FILE=""
#
#[logging]
#ETCD_DEBUG="false"
# examples for -log-package-levels etcdserver=WARNING,security=DEBUG
#ETCD_LOG_PACKAGE_LEVELS=""

/etc/kubernetes/config

###
# kubernetes system config
#
# The following values are used to configure various aspects of all
# kubernetes services, including
#
#   kube-apiserver.service
#   kube-controller-manager.service
#   kube-scheduler.service
#   kubelet.service
#   kube-proxy.service
# logging to stderr means we get it in the systemd journal
KUBE_LOGTOSTDERR="--logtostderr=true"

# journal message level, 0 is debug
KUBE_LOG_LEVEL="--v=0"

# Should this cluster be allowed to run privileged docker containers
KUBE_ALLOW_PRIV="--allow-privileged=false"

# How the controller-manager, scheduler, and proxy find the apiserver
KUBE_MASTER="--master=http://master:8080"


/etc/kubernetes/apiserver

###
# kubernetes system config
#
# The following values are used to configure the kube-apiserver
#

# The address on the local server to listen to.
KUBE_API_ADDRESS="--address=0.0.0.0"

# The port on the local server to listen on.
# KUBE_API_PORT="--port=8080"

# How the replication controller and scheduler find the kube-apiserver
KUBE_MASTER="--master=http://master.168.0.65:8080"

# Port minions listen on
# KUBELET_PORT="--kubelet-port=10250"

# Comma separated list of nodes in the etcd cluster
KUBE_ETCD_SERVERS="--etcd-servers=http://master:2379"

# Address range to use for services
KUBE_SERVICE_ADDRESSES="--service-cluster-ip-range=10.254.0.0/16"

# default admission control policies
#KUBE_ADMISSION_CONTROL="--admission-control=NamespaceLifecycle,NamespaceExists,LimitRanger,SecurityContextDeny,ServiceAccount,ResourceQuota"
KUBE_ADMISSION_CONTROL="--admission_control=NamespaceLifecycle,NamespaceExists,LimitRanger,ResourceQuota"

# Add your own!
KUBE_API_ARGS=""


/etc/kubernetes/kubelet

###
# kubernetes kubelet (minion) config

# The address for the info server to serve on (set to 0.0.0.0 or "" for all interfaces)
KUBELET_ADDRESS="--address=0.0.0.0"

# The port for the info server to serve on
# KUBELET_PORT="--port=10250"

# You may leave this blank to use the actual hostname
KUBELET_HOSTNAME="--hostname-override=master"

# location of the api-server
KUBELET_API_SERVER="--api-servers=http://master:8080"

# pod infrastructure container
KUBELET_POD_INFRA_CONTAINER="--pod-infra-container-image=registry.access.redhat.com/rhel7/pod-infrastructure:latest"

# Add your own!
KUBELET_ARGS=""

啟動服務 :

for SERVICES in etcd kube-apiserver kube-controller-manager kube-scheduler; do
    systemctl restart $SERVICES
    systemctl enable $SERVICES
    systemctl status $SERVICES
done

 

觀看 port 啟動狀況  netstat -natp
 

/etc/sysconfig/flanneld"

# Flanneld configuration options
# etcd url location.  Point this to the server where etcd runs
#FLANNEL_ETCD_ENDPOINTS="http://127.0.0.1:2379"
FLANNEL_ETCD_ENDPOINTS="http://master:2379"

# etcd config key.  This is the configuration key that flannel queries
# For address range assignment
FLANNEL_ETCD_PREFIX="/atomic.io/network"

# Any additional options that you want to pass
#FLANNEL_OPTIONS=""

 

設定 flannel 網段

etcdctl mk /atomic.io/network/config '{"Network":"172.17.0.0/16"}'

 

設完後再全重啟

for SERVICES in etcd flanneld docker kube-apiserver kube-controller-manager kube-scheduler kubelet kube-proxy; do
    systemctl restart $SERVICES
    systemctl enable $SERVICES
    systemctl status $SERVICES
done
 

 

設定  Kubernetes Minions (Nodes) (三台都安裝 flannel kubernetes)

1
$ yum -y install flannel kubernetes

 

編輯  /etc/sysconfig/flanneld

 

# Flanneld configuration options
# etcd url location.  Point this to the server where etcd runs
#FLANNEL_ETCD_ENDPOINTS="http://127.0.0.1:2379"
FLANNEL_ETCD_ENDPOINTS="http://master:2379"

# etcd config key.  This is the configuration key that flannel queries
# For address range assignment
FLANNEL_ETCD_PREFIX="/atomic.io/network"

# Any additional options that you want to pass
#FLANNEL_OPTIONS=""

編輯 /etc/kubernetes/config

###
# kubernetes system config
#
# The following values are used to configure various aspects of all
# kubernetes services, including
#
#   kube-apiserver.service
#   kube-controller-manager.service
#   kube-scheduler.service
#   kubelet.service
#   kube-proxy.service
# logging to stderr means we get it in the systemd journal
KUBE_LOGTOSTDERR="--logtostderr=true"

# journal message level, 0 is debug
KUBE_LOG_LEVEL="--v=0"

# Should this cluster be allowed to run privileged docker containers
KUBE_ALLOW_PRIV="--allow-privileged=false"

# How the controller-manager, scheduler, and proxy find the apiserver
KUBE_MASTER="--master=http://master:8080"

 

邊輯  /etc/kubernetes/kubelet

minion1:

###
# kubernetes kubelet (minion) config

# The address for the info server to serve on (set to 0.0.0.0 or "" for all interfaces)
KUBELET_ADDRESS="--address=0.0.0.0"

# The port for the info server to serve on
KUBELET_PORT="--port=10250"

# You may leave this blank to use the actual hostname
KUBELET_HOSTNAME="--hostname-override=node1"

# location of the api-server
KUBELET_API_SERVER="--api-servers=http://master:8080"

# pod infrastructure container
KUBELET_POD_INFRA_CONTAINER="--pod-infra-container-image=registry.access.redhat.com/rhel7/pod-infrastructure:latest"

# Add your own!
KUBELET_ARGS=""

minion2:

###
# kubernetes kubelet (minion) config

# The address for the info server to serve on (set to 0.0.0.0 or "" for all interfaces)
KUBELET_ADDRESS="--address=0.0.0.0"

# The port for the info server to serve on
KUBELET_PORT="--port=10250"

# You may leave this blank to use the actual hostname
KUBELET_HOSTNAME="--hostname-override=node2"

# location of the api-server
KUBELET_API_SERVER="--api-servers=http://master:8080"

# pod infrastructure container
KUBELET_POD_INFRA_CONTAINER="--pod-infra-container-image=registry.access.redhat.com/rhel7/pod-infrastructure:latest"

# Add your own!
KUBELET_ARGS=""

minion3:

###
# kubernetes kubelet (minion) config

# The address for the info server to serve on (set to 0.0.0.0 or "" for all interfaces)
KUBELET_ADDRESS="--address=0.0.0.0"

# The port for the info server to serve on
KUBELET_PORT="--port=10250"

# You may leave this blank to use the actual hostname
KUBELET_HOSTNAME="--hostname-override=node3"

# location of the api-server
KUBELET_API_SERVER="--api-servers=http://master:8080"

# pod infrastructure container
KUBELET_POD_INFRA_CONTAINER="--pod-infra-container-image=registry.access.redhat.com/rhel7/pod-infrastructure:latest"

# Add your own!
KUBELET_ARGS=""

 

啟動 kubernetes 服務

for SERVICES in flanneld docker kubelet kube-proxy; do
    systemctl restart $SERVICES
    systemctl enable $SERVICES
    systemctl status $SERVICES 
done

 

觀看服務 kubectl get nodes & services

[root@master ~]# kubectl get nodes
NAME           STATUS     AGE
node1   Ready      5m
node2   Ready      5m
node3  NotReady   8s
[root@master ~]# kubectl get nodes
NAME           STATUS    AGE
node1   Ready     5m
node2   Ready     5m
node3   Ready     13s
[root@master ~]#  kubectl get services
NAME         CLUSTER-IP   EXTERNAL-IP   PORT(S)   AGE
kubernetes   10.254.0.1   <none>        443/TCP   1h
[root@master kubernetes]#  etcdctl ls  /atomic.io/network/subnets
/atomic.io/network/subnets/172.17.102.0-24
/atomic.io/network/subnets/172.17.47.0-24
/atomic.io/network/subnets/172.17.73.0-24
[root@node1 ~]#  ip addr |grep flannel0 |grep inet
    inet 172.17.47.0/16 scope global flannel0
[root@node2 ~]#  ip addr |grep flannel0 |grep inet
    inet 172.17.102.0/16 scope global flannel0
[root@node3 ~]#  ip addr |grep flannel0 |grep inet
    inet 172.17.73.0/16 scope global flannel0

 

[root@master kubernetes]# kubectl create -f mysql.yaml
pod "mysql" created

[root@master kubernetes]# more mysql.yaml
apiVersion: v1
kind: Pod
metadata:
  name: mysql
  labels:
    name: mysql
spec:
  containers:
    - resources:
        limits :
          cpu: 0.5
      image: mysql
      name: mysql
      env:
        - name: MYSQL_ROOT_PASSWORD
          value: password
      ports:
        - containerPort: 3306
          name: mysql


root@master kubernetes]#  kubectl create -f mysql-service.yaml
service "mysql" created

[root@master kubernetes]# cat mysql-service.yaml
apiVersion: v1
kind: Service
metadata:
  labels:
    name: mysql
  name: mysql
spec:
  externalIPs:
    - 192.168.0.67
  ports:
    # the port that this service should serve on

[root@master kubernetes]# mysql -uroot -p -h192.168.0.67
Enter password:
Welcome to the MariaDB monitor.  Commands end with ; or \g.
Your MySQL connection id is 3
Server version: 5.7.17 MySQL Community Server (GPL)

Copyright (c) 2000, 2016, Oracle, MariaDB Corporation Ab and others.

Type 'help;' or '\h' for help. Type '\c' to clear the current input statement.

MySQL [(none)]> Bye

    - port: 3306
  # label keys and values that must match in order to receive traffic for this service
  selector:
    name: mysql

 

 

 

 

 

 

arrow
arrow
    全站熱搜
    創作者介紹
    創作者 echochio 的頭像
    echochio

    echochio

    echochio 發表在 痞客邦 留言(0) 人氣()